Long PVC pipes and profiles are awkward to handle with standard top-feed granulators. Many plants end up cutting scrap into short sections just to fit the hopper—adding labor, increasing dust exposure, and creating safety risks during manual handling.
A PVC-buis horizontale breker changes the feeding geometry so you can process long pieces more safely and consistently.
Energycle reference equipment page: Horizontale breekmachine voor PVC-buizen en -profielen
Belangrijkste punten
- Horizontal feeding reduces the need for manual pre-cutting of long profiles.
- Controlled infeed (rollers or pushers) stabilizes load and helps prevent jams.
- Dust extraction and access for cleaning matter more on PVC than many buyers expect.
Gerelateerde handleidingen
- Effectieve methoden voor het recyclen van PVC (mechanisch versus grondstoffen)
- PVC recycling machine maintenance (corrosion, wear, dust control)
- PVC recycling equipment selection guide
How a PVC Pipe Horizontal Crusher Works
While designs vary, most systems follow the same logic:
- Horizontal trough infeed holds long pipes and profiles along the machine axis.
- Controlled feeding mechanism (rollers or pusher) advances the material into the cutting chamber at a metered rate.
- Load-based control pauses or reverses the feed when rotor load rises, which reduces stall events on thick-walled sections.
- Screened discharge (where applicable) helps control regrind size for reuse or compounding.
Key Features to Evaluate Before You Buy
1) Infeed control and anti-jam behavior
Ask how the machine responds to:
– thick wall pipe vs thin wall pipe
– oval or deformed pipe
– bundles of shorter offcuts
Look for controlled feeding that can slow, stop, and reverse based on load feedback.
2) Cutting chamber and wear protection
PVC can be abrasive depending on fillers and contamination.
Check for:
– replaceable wear plates inside the chamber
– accessible knife mounting and adjustment procedures
– realistic knife change time (a design that is hard to service will be serviced less)
3) Dust and housekeeping design
PVC cutting can generate fine dust. Evaluate:
– dust extraction connection points
– sealing around discharge and access doors
– cleaning access without disassembly
4) Safety and guarding
Long profiles can whip or shift during handling. Prioritize:
– safe loading height and stable support in the trough
– guarded feed mechanism
– clear emergency stop placement along the infeed zone
How to Specify a Horizontal Crusher for Your PVC Scrap
To get accurate sizing and a realistic quote, prepare:
– maximum pipe diameter and wall thickness
– typical pipe length and how it is stored/handled
– target regrind size (for re-extrusion, compounding, or selling)
– contamination risks (metal inserts, dirt, rubber gaskets)
– required throughput and operating hours
If you want to compare configurations, use the checklist above and review the core specs on the Horizontale breekmachine voor PVC-buizen en -profielen pagina.
Veelgestelde vragen
Do I still need to pre-cut long PVC pipes before crushing?
Often less (or not at all) compared with top-feed granulators, because horizontal feeding supports the pipe along its length. Extremely long or bundled material may still benefit from staging/handling rules.
What’s the difference between a PVC pipe horizontal crusher and a shredder?
Horizontal crushers are typically used to granulate/crush long pipes and profiles into controlled regrind sizes. Shredders are better for bulky, irregular items and for upstream size reduction when thickness varies widely.
How do I choose the right output size?
Start from downstream use: re-extrusion blends often want controlled chip size and low fines; selling regrind may need a different screen and QC approach. Define your target spec first, then select screen/knife strategy.
How do I reduce dust when crushing PVC?
Keep knives sharp and gaps consistent (less fines), use extraction ports effectively, and design cleaning access so operators actually clean the machine on schedule.
Conclusie
A horizontal crusher is a practical buying decision when your bottleneck is handling long scrap safely and consistently. Treat sizing as a workflow exercise—not just a rotor power question: define pipe diameter/thickness, infeed behavior, contamination risks, and the output spec your downstream process accepts. If you want a baseline reference for configurations and specs, start with the equipment page: Horizontale breekmachine voor PVC-buizen en -profielen
