Vlažni drobilica · Granulator boca · Predpranje u jednoj mašini
Mokri crusher i granulator za boce
A wet plastic granulator combines size reduction, cooling, and initial rinsing. Water injection helps carry away loose contamination and control heat buildup as sorted plastic is cut, preparing the regrind for downstream washing, separation, and drying.
Wet Granulation for Contaminated Plastic Streams
Water is added directly to the cutting chamber to combine size reduction with cooling and an initial rinse. Match the machine and water circuit to the feedstock, contamination, and downstream washing process.
Integrirano predpranje tijekom drobljenja
Water helps carry away loose dirt and dust released during cutting. Label fragments, caps, and adhesive residues may still need dedicated downstream separation and washing.
Kontinuirano hlađenje
Hlađenje unutar komore pomaže u ograničavanju nakupljanja topline pa je manja vjerojatnost da će se pahuljice razmazati, omekšati ili degradirati tijekom granulacije.
Cooling and Blade Care
Water helps control cutting temperature. Blade wear also depends on sand, metal contamination, blade material, clearance, and maintenance; water injection alone does not guarantee longer service life.
Regrind Quality Control
Flake-size distribution and fines depend on feedstock, rotor geometry, knife condition, screen opening, and feeding rate. Check the regrind against downstream washing and processing requirements using representative material.
Wet Line Integration
Integrates with washing lines for sorted PET bottles or HDPE and PP containers. Coordinate wet crushing with upstream contaminant removal and downstream washing, separation, and drying.
Postavljanje prilagođene oštrice i zaslona
Match rotor geometry, blade grade, cutting clearance, and screen opening to the feedstock and required regrind. Confirm the selected configuration in the equipment specification.
Tipične primjene mokrog granulatora plastike
Ovaj stroj je najvrjedniji kada je materijalu potrebno i smanjenje veličine i mokro čišćenje prije sljedeće faze pranja ili sušenja.
Boce i posude nakon potrošnje
Crushes sorted PET bottles or HDPE and PP containers within the approved feed dimensions. Plan each material stream around its downstream separation and washing requirements.
Oporaba mokrog otpada u kući
Korisno za pretvaranje otpada od kalupljenja, puhanja ili obrezivanja u čišće pahuljice za višekratnu upotrebu kada je prisutna kontaminacija.
Priprema sirovine za liniju pranja
Prepares screened regrind for sink-float tanks, friction washers, dewatering machines, and thermal dryers. Match the particle-size distribution to the next process stage.
Recikliranje krute i fleksibilne plastike
Selected configurations can process sorted rigid plastics or PE/PP film. Film requires matched feeding, rotor, screen, and wet discharge arrangements; confirm suitability with representative material.
Kako funkcionira proces mokrog drobljenja plastike
Kontinuirani tijek rada mokre granulacije koji kombinira rezanje, pranje, hlađenje i pražnjenje u jednoj fazi.
Materijal za hranjenje s ubrizgavanjem vode
Plastika ulazi u komoru za rezanje dok se voda prska po području dovoda i rezanja.
Zdrobiti i granulirati
The rotor and fixed knives cut the material while water helps control heat buildup. Blade grade and cutting geometry depend on the selected configuration.
Ispiranje rastresite kontaminacije
Voda pomaže u uklanjanju prljavštine, papira, prašine i drugih lakih ostataka koji se oslobađaju tijekom rezanja.
Regrind određene veličine za pražnjenje
Regrind passes through the selected screen and moves to downstream washing and separation, followed by dewatering and drying. Confirm the required particle-size distribution with a material trial.
Mokri plastični granulator u odnosu na standardni suhi granulator
A dry granulator can suit clean, dry production scrap. Consider wet granulation when the material needs washing and the line can handle wet discharge, water treatment, and subsequent drying.
| Faktor odabira | Granulator za mokru plastiku | Standardni suhi granulator | Odvojeno pranje nakon suhog drobljenja |
|---|---|---|---|
| Rukovanje kontaminiranim materijalom | Suited to sorted contaminated feed entering a wet process | Bolje za čistiju sirovinu | Cleaning begins in the downstream washing stage |
| Hlađenje lopatica | Injected water helps control cutting temperature | Typically no water injection; cooling depends on design | Cooling depends on the selected dry granulator |
| Učinak predpranja | Initial rinsing during size reduction | Nema integriranog pranja | Zahtijeva potpuno odvojenu fazu pranja nakon toga |
| Najbolji slučaj upotrebe | Sorted bottles, containers, or suitable film in a wet line | Čisti interni otpad i prethodno očišćene materijale | Koristi se kada raspored linije već odvaja drobljenje i pranje |
| Integracija linija | Combines cutting and rinsing; requires a water circuit | Can operate without a washing stage for suitable clean scrap | Separate crushing, transfer, and washing equipment |
Prijeđite prstom vodoravno za prikaz cijele tablice.
Tehničke specifikacije
Reference models for wet crushing and granulation of plastic waste. Throughput depends on material, bulk density, contamination, screen opening, and feeding conditions. Confirm blade grade and rotor configuration in the quotation and validate output with representative feedstock.
| Model | Promjer rotora | Brzina rotacije | Snaga motora | Materijal oštrice | Kapacitet (kg/h) |
|---|---|---|---|---|---|
| ERM-WPG-500 | 500 mm | 550 okretaja u minuti | 45 kW | SKD11 / D2 | 500 – 800 |
| ERM-WPG-600 | 600 mm | 500 okretaja u minuti | 55 kW | SKD11 / D2 | 800 – 1500 |
| ERM-WPG-700 | 700 mm | 428 okretaja u minuti | 90 kW | SKD11 / D2 | 1500 – 2000 |
| ERM-WPG-800 | 800 mm | 370 okretaja u minuti | 110 kW | SKD11 / D2 | 2000 – 2500 |
Prijeđite prstom vodoravno za prikaz cijele tablice.
Galerija strojeva
Ključne komponente mokrog granulatora i prikazi strojeva koji se koriste u linijama za recikliranje plastike.
Crusher plastičnih boca: recikliranje PET i HDPE boca
Used as a maloženje plastičnih bočica, the wet granulator reduces sorted PET or HDPE bottles to regrind while providing cooling and an initial rinse. Separate pre-washing, label removal, and downstream cleaning depend on the incoming contamination and required output quality.
Drobljenje PET boca
Processes sorted PET bottles within the approved feed dimensions. Screen selection and operating conditions determine the flake-size distribution. Released cap and label fragments still require downstream separation, while adhesives may require hot or friction washing.
Drobljenje HDPE spremnika
Processes sorted HDPE milk and detergent bottles after emptying and suitable pretreatment. Water rinsing does not neutralize chemical residues or establish food-contact suitability; assess the feedstock and complete recycling process.
Rotor and Screen Setup for Bottles
Where specified, V-cut geometry provides a shearing action on hollow bottles. Confirm rotor design, knife clearance, and screen opening for the selected model. Screen aperture alone does not guarantee flake dimensions or fines content.
Predpranje tijekom drobljenja
Specify injection flow, recirculating-water treatment, and fresh-water make-up separately. Required flow and cleaning performance depend on throughput, contamination, and the water circuit; verify them with representative feedstock.
Pouzdana podrška tijekom cijelog životnog vijeka opreme
Od planiranja instalacije do rutinskog održavanja, naš servisni tim pomaže da vaša oprema radi sigurno, dosljedno i učinkovito.
Jednogodišnje ograničeno jamstvo
Pokrivenost obuhvaća tvorničke nedostatke na glavnim mehaničkim i električnim komponentama tijekom jedne godine. Dijelovi podložni normalnom habanju i oštećenja uzrokovana nepravilnim rukovanjem obrađuju se zasebno.
Upute za instalaciju
Pružamo smjernice za raspored, temelj, priključke, slobodan prostor, integraciju u liniju i puštanje u rad kako bismo podržali nesmetanu instalaciju i pouzdano pokretanje.
Opskrba rezervnim dijelovima
Zamjenski trošni dijelovi, ležajevi, brtve, senzori, električne komponente i ostali servisni artikli dostupni su za planirano održavanje i dugoročno rad.
Tehnička podrška
Daljinska dijagnostika kvarova, preporuke za rad, upute za održavanje i opcionalna servisna podrška na licu mjesta dostupni su kada vaš projekt treba dodatnu podršku.
Često postavljana pitanja
Česta pitanja o mokrom drobljenju, konfiguraciji lopatica, potrošnji vode i integraciji linije.
Water injection combines cutting with cooling and an initial rinse. It can help carry away loose contamination before downstream washing. Results depend on the material, contamination, knife condition, screen opening, and water circuit.
No. Wet granulation provides size reduction and initial rinsing. Depending on the feedstock and required output, a line may also need pretreatment, hot or friction washing, separation, rinsing, and drying. Wet crushing alone does not establish suitability for food-contact use.
The reference models list SKD11 / D2 blades. Confirm the blade grade, rotor geometry, cutting clearance, and screen opening for the selected model in the quotation. Validate flake-size distribution and fines with representative material.
Applications include sorted PET bottles, HDPE or PP containers, and suitable production scrap. PE/PP film requires matched feeding, rotor, screen, and discharge arrangements. Confirm each material stream, feed dimensions, contamination, and required output before choosing the configuration.
Confirm water injection flow, circulating flow, and fresh-water make-up separately. Requirements depend on throughput, contamination, discharge design, and water treatment. A recirculation loop needs appropriate solids removal and water-quality control; there is no single water-use figure for every model and material.
Konfigurirajte mokri granulator plastike za svoju liniju za recikliranje
Pošaljite nam vrstu materijala, razinu kontaminacije, ciljani protok i nizvodni proces. Preporučit ćemo vam odgovarajući model mokre drobilice, postavku lopatica i prateću opremu.